Moving sale Every Bullfrog hot tub at our cost Ends Friday, Oct 30th

Pool Closing Guide: When and How to Close Your Pool

brand new pool and landscape project built in Kingston

Close your pool once overnight temperatures stay below 65°F (18°C) for good. For Kingston, Napanee, Belleville and Prince Edward County, that’s typically the last two weeks of September through mid-October. Closing too early risks algae blooming in warm water sealed under a cover; closing too late risks a hard freeze cracking a skimmer, heater or pipe before you get the water out. Below is the full step-by-step process, the water chemistry targets to hit before you cover up, and the mistakes that turn into expensive spring repairs.

When to Close Your Pool

Water temperature, not the calendar, is the real signal. Once your pool water holds steady below 65°F (18°C), algae growth slows enough that sealing the pool under a cover won’t turn it green by spring. In our service area, that usually lands in late September to mid-October, but a cold snap can pull it earlier and a warm fall can push it later, so check the actual water temperature rather than going by date alone. Our full seasonal service guide covers the booking windows for every service, not just pool closing.

Closing early, while the water is still warm, is the most common mistake we see. Algae and bacteria multiply fast in warm, still, covered water, so an early close often means an ugly reopening. Closing too late is the other risk: once overnight lows start dropping near freezing, any water left in pipes, the pump, filter or heater can freeze, expand and crack the equipment, and that damage isn’t cheap to replace.

What You’ll Need Before You Start

Gather everything before you start draining water. Once the level is down and lines are blown out, you don’t want to be running to the store mid-job while the pool sits half-closed overnight.

  • Pool closing chemical kit: chlorine-free shock, algaecide, and a stain & scale preventer
  • Test strips or a liquid test kit for pH, alkalinity and calcium hardness
  • A winterizing/air plug kit and either an air compressor or a shop-vac (blower mode) to clear the lines
  • Pool antifreeze (non-toxic, RV-grade, never automotive antifreeze) for exposed plumbing
  • A properly sized safety or winter cover, plus water bags or a cover pump if you expect rain or meltwater
  • A skimmer net, pool brush and a vacuum for a final clean
In-ground pool built by Quality Landscape Group in Kingston, Ontario, ready for fall pool closing
An in-ground pool we built in Kingston, ON, ready for its fall closing before the first hard frost.

How to Close a Pool, Step by Step

Step 1: Deep Clean the Pool

Brush the walls and floor, skim the surface, and vacuum out anything that settled. Anything organic left in the pool over winter feeds algae and stains the plaster or liner by spring.

Step 2: Balance the Water Chemistry

Test and adjust pH, total alkalinity and calcium hardness before you do anything else. Shock and algaecide only work properly in balanced water. See the target ranges in the table below.

Step 3: Shock the Pool

Add a chlorine-free winterizing shock the evening before you close, after the sun goes down so it doesn’t burn off. This knocks out any bacteria and algae spores before the pool gets sealed up for months.

Step 4: Add Algaecide and a Stain & Scale Preventer

A winter-strength algaecide, added after the shock has had a few hours to work, is what actually keeps the water clear under a dark cover for five-plus months. A stain and scale preventer protects a liner or plaster finish from the minerals left behind as water sits.

Step 5: Lower the Water Level

Drop the water level below the skimmer and any inlet fittings, typically 4-6 inches below for a mesh safety cover, or down to the light fixtures for a solid winter cover. This keeps freezing water from cracking the skimmer housing or fittings.

Step 6: Drain and Blow Out the Plumbing

Water left in pump, filter, heater and underground lines is the single most common source of winter freeze damage. Drain the equipment, then use an air compressor or shop-vac to blow remaining water out of every line until air bubbles stop, and cap the lines. Add non-toxic pool antifreeze to skimmer and return lines as a backup, never as a substitute for actually clearing the water.

Step 7: Remove and Store Accessories

Ladders, rails, solar covers, skimmer baskets and automatic cleaners all come out. Rinse them, let them dry, and store them somewhere they won’t crack in freezing temperatures.

Step 8: Install the Winter Cover

A properly sized safety cover or winter cover, secured tightly with no low spots for water to pool, keeps out debris and sunlight (which is what starves off algae growth) for the whole winter. A cover that’s too loose collects water and stress that shortens its own lifespan.

In-Ground vs. Above-Ground Pool Closing Differences

The chemistry and shocking steps are identical either way, but the physical process differs enough to plan for:

In-ground pools have plumbing that runs underground to the pump and filter, which is exactly why blowing out every line matters so much: a frozen underground line is a dig-and-repair job, not a quick fix. In-ground pools also typically use a mesh or solid safety cover anchored into the deck around the perimeter.

Above-ground pools have shorter, more accessible plumbing (often just a hose-style connection to an external pump), so there’s less risk of hidden trapped water. The main extra step is installing an air pillow under the winter cover before securing it. The pillow absorbs the expansion of ice forming at the surface so it pushes up against the pillow instead of against the pool wall.

Pool Water Chemistry Targets for Closing

Balance these before you shock the pool, not after. The CDC recommends pool pH stay between 7.0 and 7.8, and the ranges below build in the margin that keeps water stable under a cover for months rather than weeks.

ParameterTarget Range for ClosingWhy It Matters
pH7.4 – 7.6Outside 7.0–7.8, chlorine and algaecide lose effectiveness (CDC)
Total Alkalinity80 – 120 ppmBuffers pH so it doesn’t swing over winter
Calcium Hardness200 – 400 ppmPrevents liner/plaster etching or scaling
Free Chlorine (before shock)1 – 3 ppmConfirms sanitizer is active before you add shock
A well-maintained in-ground pool built by Quality Landscape Group, kept swim-ready every season
A properly maintained pool stays swim-ready season after season, the payoff of closing it right each fall.

DIY vs. Professional Pool Closing

Both work. The right choice depends on your equipment, your comfort level with an air compressor around plumbing, and how much of your Saturday you want back. If you’d rather have it handled, our pool care team closes pools throughout the region every fall.

DIY ClosingProfessional Closing
Time required2–4 hours, plus buying suppliesBooked and done same visit
Equipment neededYou supply air compressor, chemicals, winterizing plugsCrew brings everything
Risk of missed water in linesHigher; easy to miss a line without experienceLower; checked line by line as standard practice
CostSupplies only, typically $80–150Flat service fee, no guesswork on chemical amounts
Best forComfortable DIYers with the right equipment on handAnyone who wants it done right the first time, no spring surprises

Common Pool Closing Mistakes That Cause Spring Problems

Most spring pool headaches trace back to one of five mistakes made during closing the previous fall. Watch for these:

  • Closing on the calendar, not the water temperature: a warm October leaves algae time to bloom under the cover.
  • Skipping the shock treatment: the single biggest cause of a green pool at opening.
  • Leaving water in the lines: the most expensive mistake, since a cracked heater or underground line isn’t a cheap fix.
  • Using automotive antifreeze instead of pool-grade antifreeze: automotive antifreeze is toxic and shouldn’t go anywhere near pool plumbing.
  • A loose-fitting cover: collects standing water and debris, and won’t stop light-driven algae growth the way a taut cover does.

Regional Closing Timeline for Kingston, Napanee & Belleville

Every property and every fall is a little different, but this is the general window we work to across the region:

TimeframeWhat to Do
Early-to-mid SeptemberStart tapering feeding of algaecide/phosphate remover as the water begins cooling; book your closing appointment
Late September – mid-OctoberStandard closing window once water holds below 65°F (18°C)
After the first hard frostToo late to safely drain lines without risk; equipment may already be damaged

Frequently Asked Questions

What temperature should I close my pool at?

Close once the water holds steady below 65°F (18°C), not by a fixed date. In our region that’s usually late September through mid-October, but check the actual water temperature since a warm fall can push that later.

Can I close my pool too early?

Yes. Closing while the water is still warm gives algae and bacteria ideal conditions to grow under a sealed, sun-blocked cover, which is the most common reason a pool opens green in spring.

Do I need to hire a professional to close my pool?

No, but it removes the guesswork. A professional closing checks every line for trapped water: the step most likely to be missed by a first-time DIYer and the one that causes the costliest winter damage.

What happens if I don’t close my pool properly?

Water left in pipes, the pump or the heater can freeze and crack the equipment, and unbalanced or unshocked water often turns green under the cover, and both mean added repair or cleanup cost before you can swim again.

How much does a professional pool closing cost?

Pricing depends on pool size, equipment and accessories, so we price each closing after a quick look at the setup rather than a flat rate. Contact us for a quote specific to your pool.

Ready to Book Your Service?

Call now or request a free quote online, we serve Kingston, Napanee, Belleville and Prince Edward County.

40+ Years ExperienceFully Insured & WSIB5-Star Rated on Google